DVD Rebuilder 1.26.3 Pro

[mitomcua]

Below is the official change log for DVD Rebuilder Pro version 1.26.3:
Fixed an error in which the REDIST_ALL parameter was not being set correctly when selected. In the previous version any change to the setting was not recognized until the next program load.
Added Beta support for command line oriented encodes (e.g. Mencoder or FFMPEG). DVD-RB will call a pre-configured .BAT file that can be setup for the calls.An example .BAT file (for mencoder) is included as an example.In order to use it, you must edit it (it is normally found in the "c:\Program Files\DVD-RB Pro\Encoders" directory) and point ensure the path properly points to MENCODER.EXE.You must also add the line "cmdline=" to the "[Paths]" area of the REBUILDER.INI file. This new option should be considered in Beta test until it has been used more.My encodes (using M encoder) so far tend to be under-size -- but very good quality.Try the "Good (fast)"mode, it gives very good quality and is exceptionally fast.Be careful with "Highest Quality" mode -- it can be slow.
Added an option to the MODE menu in which you can choose to always use HC as the encoder for REDISTRIBUTION.This prevents a rare CCE problem that can happen when high bitrate matrices are in use.
Updated REDISTRIBUTION so that any cell with 500 or fewer frames would redistribute using 100% sample.This prevents lower-than-required bitrates on small segments that have blackness or fade-ins that might undervalue the need.
Moved "Shutdown at REBUILD Completion" and "Close DVD-RB at REBUILD" completion from the MODE menu to the FILE menu. This makes it possible to change the state of these options while DVD-RB is executing.
Corrected a bug in which, under certain circumstances, it is possible to receive a "Runtime Error 53" message during REDISTRIBUTION.
Corrected an minor bug in which bitrates for single frame segments were incorrectly REDISTRIBUTED.
Corrected an error in which attempting to use the "No Compression" encoder option with REDISTRIBUTION enabled could cause DVD-RB to abort with errors (87/13)
Updated the response to errors resulting from a corrupt source (VOBID/CELLID not found errors) so you have the option to continue as opposed to a forced exit.Note however that it is not usually a good idea -- as this is an indicator of a pretty serious corruption in the source IFO/VOB combination.
Other minor and cosmetic changes.

Encoders:

Canopus ProCoder v2.04.02 Cracked Enhanced Version
Canopus Procoder v3
Cinema Craft Encoder Basic Version 2.70.01.14 RETAIL
Cinema Craft Encoder SP v2.70.02.12 RETAIL

[HIDE-REPLY]http://www.megaupload.com/?d=IKAUCEL0[/HIDE-REPLY]

[laodai]

hình như DVD Rebuilder 1.26.3 Pro no audio ,please use 1.26.5;) :) thanks

[mitomcua]

hình như DVD Rebuilder 1.26.3 Pro chi ở vietstuff.org có thôi ,mình đi seach mấy ngày rồi không thấy ;) :) thanks

You are absolutely right

[kumoi]

That's where DVD ReBuilder (DVD-RB) comes in. This program was built to bridge the gap between the incredibly easy but limited "one-click" solutions and the incredibly complex but high-quality methods of DVD ripping and backup. Another advantage of DVD-RB when compared to older methods is that it doesn't require access to an expensive authoring package. DVD-RB includes its own reauthoring engine that reconstructs the DVD in a way compatible with its original design.

Over the course of the past couple of years DVD ripping techniques have changed dramatically. Newer "one click" programs have made backing up a DVD a fairly simple process... but there is a significant trade-off. The quality that can be attained by even the best of these programs is poor in comparison to original techniques that used Cinemacraft Encoder, TMPGEnc, or other top-notch encoders. The reason is simple. When using one of these encoders the picture is rebuilt from scratch and optimized for the resulting bit rate. One-touch transcoders usually change quantization and/or motion info in order to lower the bit rate. This can result in pixelation and poor overall picture.

DVD Rebuilder PRO features:
- Closed Captions - Now DVD-RB will extract closed caption data from the original DVD and remultiplex it into the MPEG stream during REBUILD.
- Menu Encoding - The ability to scan and reencode menu segments in the same way as standard title sets.
- Multiple encoder instances - On multiple core computers and some very fast single core computers using hyperthreading this will take advantage of unused processor time.
- Movie and Menus Only capability - allows you to get the best quality within limited available space.
- Movie and Menus Only capability - allows you to get the best quality within limited available space.
- Segment Blanking - Provides you a capability to remove annoying intro screens.
- Slideshow Mode - Convert "Extra" segments into a slideshow, saving valuable space for the Feature.
- Advanced Encoding Features - Modify GOP size, add customized encoder quantizer matrices, set DC precision.
- Movie-Only - mode that gives the highest quality possible. Every available bit is dedicated to the feature.
- One pass encoding support for HC encoder - Gives high quality results in much less time.
- Graphic Analysis display for use in analyzing the IFO structure - draws PGC/CELL relationships.
- ISO file creation is now supported to make it easier to archive or burn DVD-RB's output.
- Automatic burning using ImgBurn or DVD Decrypter - makes complete DVD Backup truly "one-click".
- Remapping audio tracks - set the default to your language or preferred format.
- New intuitive interface - modernizes and simplifies control of your rebuild!
- Full support for video interleaving (ILVU) - re-encodes angle and seamless branching.
...and more... with many additional features planned in the near future!

Changes in version 1.26.5:
- Added a REDISTRIBUTION threshold test that limits the amount of low-side deviation allowed in the calculation of redistribution. The default value of .5 limits a bitrate reduction (in redistribution) to half what would have been given in a standard DVD-RB encode. This dramatically reduces the likelihood of getting values that are too low in dark scenes. The threshold can be adjusted via a hidden setting in the OPTIONS area of REBUILDER.INI. The value (REDIST_LOW_THRESHOLD=) must fall in the range of 0 to 1. Any other value results in the default of .5
- Added a "hidden" setting called "REDIST_USE_FINAL_Q". If set to 1 (REDIST_USE_FINAL_Q=1) in the "[Options]" area of REBUILDER.INI, a set of prediction passes are run on the main-movie VTS (largest) to determine a Final_Q value that is used for REDISTRIBUTION rather than the standard Base_Q. This will add a little time to the PREPARE phase and some reports have been made of improved quality based upon subjective analysis.
- Corrected an error in which pushing the ABORT button could, under certain circumstances, leave an encoder executing in the background until it completes its current task. It might also result in a "Could not clear output..." error if an attempt to restart encoding happens too soon.
- Updated "Batch Mode" so that it will, when appropriate, write to blank disc. Note that you must (obviously) change discs between writes in order to write more than one during the batch process.
- Added a separator bar to the FILE menu to distinguish the "Shutdown on REBUILD" functions from those related to Batch.
- Added code to limit the sample size to 1% when performing REDISTRIBUTE_FINAL_Q analysis. Any more is simply a waste of time. Note this does NOT affect the percentage used for determining REDISTRIBUTION -- only determining FINAL_Q.
- Corrected two bugs that were introduced in v1.26.4 (which was released as a beta only).
- Other minor and cosmetic changes.
FULL

CODE
http://rapidshare.com/files/61361039/DVDR1265PRO.rar

or:
http://www.megaupload.com/?d=VJGMX2I4

im testing now.....

[fsquare]

i want to try. thank you so much XD

[laodai]

dvd rebuild 1.26.3 no audio bro sài 1.26.5